[. . . ] · Do not use any lead, switch or cord other than the one supplied with this blanket. · Not intended for medical use in hospitals. Care instructions · Examine frequently for any signs of wear or damage to the blanket, switch or cord. In case of damage or misuse, cease using and contact The After Sales service helpline (See page 6) · During the summer, the blanket can be used to air the mattress. · Do not dry clean the blanket, follow washing instructions on the label attached to the blanket and the details that relate to your blanket. 2 75142 rev1 17/3/06 10:10 AM Page 3 Electrical requirements Check that the voltage on the rating label of your appliance corresponds with your house electricity supply which must be A. C. [. . . ] · WARNING: Ensure the blanket is not folded, rucked or creased. When in use do not cover with pillows. Fitting instructions · Each blanket is fitted with 3 tie tapes. · Position the blanket on the bed ensuring the pillow area is clear. · Repeat for second tape ¤ at opposite end of the blanket. · Pass the centre tape < underneath the mattress and tie to opposite loop. · If the blanket is stretched too tightly, not allowing for `give' of mattress when the bed is occupied, distortion of the edges may take place. A / < ¤ Tie off 10-15 cm 4-6 inches 4 75142 rev1 17/3/06 10:10 AM Page 5 How to use 1 Ensure the blanket is fitted to the bed correctly, see diagram A, page 4 2 Plug the power lead into the closest socket, using an extension lead if needed to ensure that the lead is not stretched. Machine washing 1 Unplug the blanket from the power socket. 2 Disconnect the control switch and cord from the blanket by lifting the locking lever over the raised button and pull apart. 4 Gently stretch the blanket back to it's original shape and size before drying WITHOUT using clothes pegs on the wired area of the blanket. (See instrucions for tumble drying) Preheating the bed 1 Move the heat setting on the control switch to heat level 2 or 3, depending on the level of the heat required. Allow approximately 60-90 minutes for the blanket to heat the bed thoroughly, although this time may vary depending on the room temperature and type of bedding used. Tumble drying 1 Unplug the blanket from the power socket. 2 Disconnect the control switch and cord from the blanket by lifting the locking lever over the raised button and pull apart. 3 Tumble dry on the LOW heat setting, following the drying under `machine washing' section, point 4. B All night use 1 Move the heat setting on the control switch to heat level 1. · This setting will provide safe and comfortable heat to sleep on all night. WARNING: Always ensure that the heat setting is moved to the OFF position when you get up the next day, or after airing the bed. Washing instructions · Do NOT dry clean · Do NOT iron WARNING:Before washing ensure that you detach all the controls from the blanket. · Only use a washing machine with a drum large enough to take the blanket without forcing it in. 1 Measure the blanket so it can be stretched back to its original size whilst wet. Hand washing 1 Unplug the blanket from the power socket. 2 Disconnect the control switch and cord from the blanket by lifting the locking lever over the raised button and pull apart. 3 Use a mild washing liquid or detergent and lukewarm water. 5 75142 rev1 17/3/06 10:10 AM Page 6 4 Immerse the blanket in the water and allow to soak for 5-10 minutes. 6 Rinse the blanket thoroughly in cool water, gently squeezing the fabric. [. . . ] This guarantee does not confer any rights other than those expressly set out above and does not cover any claims for consequential loss or damage. This guarantee is offered as an additional benefit and does not affect your statutory rights as a consumer. · This guarantee is valid in the UK and Ireland only. All Morphy Richards products are individually tested before leaving the factory. In the unlikely event of any appliance proving to be faulty within 28 days of purchase it should be returned to the place of purchase for it to be replaced. [. . . ]